Airsoft Electric Guns require minimal cleaning. The most important part that should be cleaned regularly is your barrel.
To clean your barrel, take your cleaning rod and thread a .22 caliber patch (or similar sized patch of cloth) through the slit. Spray a small amount of silicon spray to the patch.
Before inserting your cleaning rod into the barrel, turn your hop up off. If you leave your hop up on you run the risk of damaging your hop up and getting your cleaning rod stuck.
Insert your cleaning rod into the barrel. Swab the inside of the barrel with a back and forth motion. Remove the patch from your cleaning rod. Insert a new, dry patch into the slit and repeat the process to clear any remaining residue from the inner barrel.
Once there is no dirt left in the barrel, test fire your gun and reset the hop up.
We recommend you have your Automatic Electric Gun gearbox cleaned and relubricated every 6 months, depending on how heavily your gun is lubricated. This should be performed by a trained professional.
Unjamming airsoft guns:
Airsoft guns typically jam due to excessive dirt in the barrel, dirty BBs, deformed BBs, foreign objects in the magazine or barrel, or overly tight hop up. In more extreme cases, a gun can jam due to a damaged or deformed hop up bucking, damaged nozzle, or damaged tappet plate.
If a BB jams in the gun stop firing it immediately. Continued firing may result in a broken gear or piston.
Use the opposite end of your cleaning rod. The tip has a slanted angle. Turn your hop up off and insert that end into the barrel. Turn the gun upside down to look at the magazine well. Gently force the BB back into the area of the magazine well.
Once the BBs have been cleared from the barrel, test fire the gun without any BBs. If the gun sounds fine, test fire it again with BBs. If jamming persists, consult with your local airsoft Dealer regarding repairs.
BBs:
Only use premium brand BBs with Automatic Electric Guns. Using cheaper BBs may cause damage to your gun and barrel due to seams, burrs, and deformation of the BBs resulting from poor manufacture. These guns are designed for 0.20 gram weight BBs or heavier. Any BBs lighter than 0.20g will cause a jam or breakage.
*WARNING*: Do not reuse BBs. Reusing BBs may also cause a jam or breakage in your gun.
If you are not sure about what BBs to use, consult with your Spartan authorized Dealer regarding what type of BBs to use.
Loading magazines:
Be sure to thoroughly read your manual on loading magazines. Make sure your BBs are clean and new. Dirty or deformed BBs can cause your magazine or gun mechanisms to jam.
Keep foreign objects, debris, and dirt away from your BBs and your magazines.
Always remove and throw away the staple from your bag of BBs! They are notorious for jamming magazines.
Occasionally lubricate your magazines by spraying a small amount of 100% silicone lubricant into the magazine. If you magazine has been subjected to significant amounts of dirt and dust, you will need to disassemble your magazine and clean out all of the dirt and dust. Consult with your local airsoft Dealer on how to do this.
High capacity magazines are fairly complex mechanisms. In order for them to feed reliably, at least 50 BBs must be loaded in them. There will always be 20 BBs left in the magazine. A fully wound magazine will typically shoot 50%-75% of the magazine's full capacity before requiring rewinding. You can overwind high capacity magazines; if the winding wheel is clicking, it is overwound. If a high capacity magazine jams, tap the side of the magazine sharply against a solid surface. That will unjam the winding wheel.
Motor height adjustment: A key component of proper gun functioning is the motor height set screw. This small hex screw (typically 1.5mm in width) is located at the end of motor housing, typically located in the grip of the gun. This screw ensures that the motor is set the proper distance from the gears in the gearbox. If the motor is too close or too far from the .bevel. gear of the gearbox, you will hear a soft or loud whine from the gun. In extreme cases, an improperly set screw will cause the gun to jam, break the gear, or strip the pinion gear on the head of the motor.
Your motor height is set in place by the factory. After heavy use, the spinning of the motor may cause the set screw may tighten or loosen from its original position. You may notice unusual noises coming from your gearbox. You will need to adjust the screw into its proper position. ·
A high pitch whining sound indicates your motor height may be too low. To correct this, you must turn the set screw clockwise to raise the motor up. Do this slowly while firing the gun in semiautomatic. Listen for a flat, consistent sound; the same that you heard when you fired the airsoft gun for the first time. Once you.ve achieved this, leave the screw in place. ·
A high pitch, grinding sound indicates your motor is too high, or you have adjusted too far. Turn the screw counterclockwise to lower the motor while firing in semiautomatic. Again, listen for flat, consistent sound coming from your motor and gears. ·
The key to adjusting the motor height is to minimize any sounds coming from your motor and gearbox.
Fuses: Fuses prevent a sudden discharge from your battery into the gun that may potentially damage your motor or other electrical contacts in your gearbox.
If your gun stops firing for any reason, the first thing you should check is the fuse.
If the metal strip in your fuse is no longer intact, replace the fuse with another one (easily available at your local hardware store) and test the gun again.
The most common reason for a fuse to blow is low battery charge. The motor will not turn due to lack of energy but the battery still has sufficient charge to heat up the wiring and blow the fuse. Replace the fuse, recharge your battery, and try again. Should your gun be 'locked up', i.e. your gun will not fire even with a fully charged battery, consult with your local airsoft Dealer on services to unlock the gearbox and make sure no parts were damaged. ·
You can replace a broken fuse with one rated up to 30 Amps.
Field care:
*ATTENTION*: Treat your airsoft guns with care when handling. Though these products are made mostly of metal parts and are considered quite durable, it will not withstand the abuses and tolerances of a real firearm. Any type of major impact to the airsoft gun can potentially cause damage that will effect the performance or possibly break.
Avoid direct impacts to the barrels and stocks. Barrels can bend and render the gun inoperable.
Avoid jamming dirt into the barrels. If a significant amount of dirt and debris travels up the barrel, have a professional airsoft Dealer inspect it and clean it. ·
Use a sling whenever possible to avoid dropping the gun. ·
After use, be sure to clean the gun thoroughly as described in the cleaning FAQ.
Many external components of the gun are attached by screws. Before and after use, check to see if any of these screws have loosened. If so, tighten them gently. Do not over torque the screws as that may cause screw threads to strip.
If any parts are damaged or broken, contact your airsoft Dealer about obtaining replacement parts.
Gun repair and upgrades:
Gun repairs not described in these FAQs should only be performed by an experienced airsoft Dealer. Contact your local airsoft Dealer for what repair services they offer or for referral to an experienced professional who specializes in repairs.
Airsoft guns are designed to perform within certain parameters and tolerances. Changes made to these parameters and tolerances are not recommended and are done at your own risk. Alteration to the gun's internal parts may cause excessive wear and tear, and possibly breakage. Alteration to the gun's internals will void any factory warranties.
Consult with your local airsoft Dealer for more information regarding gun upgrades.
